AI-generated application image of a technician placing amber polyimide masking dots on a PCB before conformal coating.

Polyimide Masking Dots for PCB Conformal Coating: Selection and Application Guide

Polyimide masking dots can protect circular keep-out areas during PCB conformal coating. A successful mask must fit the board drawing, stay in place through the coating cycle and release without damaging the assembly or coating boundary. Selecting a heat-resistant film is only one part of that decision.

This guide explains what to check when evaluating APT Polyimide Dots. Use it to prepare a production trial alongside the coating manufacturer's instructions and your assembly requirements.

Start with the PCB masking drawing

Mark each area that must remain free of coating. A circular dot works best where the required protected boundary is circular and the operator can place it accurately. Connector contacts, irregular features and openings may need a different masking shape or method.

Specify the protected diameter and placement tolerance before ordering. A disc that is too small can expose part of the keep-out area; one that is too large can prevent coverage where coating is required. Check the fit on an actual assembly, including nearby components and access for removal.

Check the complete tape construction

APT Polyimide Dots use 1 mil polyimide film with 1.5 mil silicone adhesive, giving 2.5 mil total thickness. The listed temperature rating is 500°F / 260°C. These figures describe the die-cut product; do not substitute specifications from a separate roll tape.

The product is described as commercial-grade polyimide. Kapton is a brand of polyimide film, so the material name alone does not establish that these dots use Kapton-branded film.

Confirm adhesive and coating compatibility first

Tell the coating supplier that the proposed dot has silicone adhesive. Ask whether that construction is acceptable for the exact coating, board-cleaning procedure and contamination-control requirements. If your process requires a silicone-free masking adhesive, this construction does not meet that requirement.

Do not assume that a high temperature rating establishes compatibility with every coating or solvent. Evaluate the entire sequence: cleaning, masking, coating application, drying or curing, mask removal and any later processing.

Explore APT masking dots

Polyimide Dots

Review diameters, liner options and current product specifications.

View product options

Choose diameter and liner for accurate placement

APT lists standard diameters from 1/8 inch to 2 inches. Dots 3/8 inch or larger include a split-back liner; smaller split liners and custom sizes are available on request. Check the quantity for the selected diameter when planning production.

Consider how the operator will peel, position and retrieve each dot without touching sensitive areas. Follow the site's ESD handling procedure and use tools approved for the assembly. Avoid stretching the mask or forcing it across a feature that prevents full edge contact.

Run a representative application and removal trial

  1. Prepare the assembly: use the approved cleaning method and allow the area to dry. Confirm that cleaning leaves no incompatible film.
  2. Apply the dot: position it within the drawing tolerance and press the perimeter evenly without damaging components.
  3. Process the board: use the actual coating method, thickness, drying conditions and cure cycle planned for production.
  4. Remove at the validated stage: follow the coating and masking suppliers' guidance. Do not select a removal temperature or timing from the film rating alone.
  5. Inspect the result: check for coating beneath the mask, residue, lifted coating, board damage and incomplete coverage around the boundary.

Record the material, diameter, coating, process conditions and inspection result. Repeat qualification when a relevant material or process changes rather than relying on the appearance of the masking film.

Common PCB masking questions

Can any polyimide dot be used with any conformal coating?

No. Confirm the adhesive construction, coating chemistry, contamination requirements and complete processing cycle. A film temperature rating is not a universal coating-compatibility approval.

Should masking dots be removed before or after cure?

Use the removal stage specified for the coating and masking combination, then validate it on representative assemblies. There is no single timing rule suitable for every coating system.

Can a used masking dot be applied to another PCB?

Do not assume reuse is acceptable. Include any proposed reuse in process qualification and inspect for contamination, coating buildup, damaged edges and loss of adhesion.

Prepare your masking-dot enquiry

Send APT your required diameter or drawing, quantity, coating system, peak temperature, exposure duration and any silicone-free requirements. For a broader material comparison, read Paper vs Polyester vs Polyimide Masking Dots, or contact APT for application guidance.

Explore APT masking dots

Polyimide Dots

Review diameters, liner options and current product specifications.

View product options

Regresar al blog

Deja un comentario

Ten en cuenta que los comentarios deben aprobarse antes de que se publiquen.